Jul 14, 2018 Leave a message

Bright steel wire surface finish and tolerance range

Description of the surface finish and tolerance range of bright steel wire

 

 Technical parameters of bright steel wire: especially the bright steel wire produced by the water tank drawing machine.

 1. Surface finish

There is basically no residue of the brushed lubricant on the surface, but there is a little residue, which can be left by hand to leave a small amount of black oil stain;

 1.1 There is no black oil on the surface. The steel wire with no black oil residue is rubbed by hand. Except that it is produced by pickling process, it is because the steel wire has damaged the steel wire surface and damaged the steel wire due to mold damage or variability during drawing. Roundness, such steel wire should be a defective product.

 1.2 The surface of the pseudo-bright steel wire has been embedded with a lot of brushed lubricant. The gloss of the appearance comes from the polishing effect in the drawing process. The black oil residue is rubbed by hand. The biggest harm is that the wire is welded to the condenser or the evaporator. It cannot be removed in the subsequent coating process, so the salt spray test cooperation cannot be guaranteed, and the service life of the product is greatly reduced, which is easy to rust during use. This product is not a bright steel wire. Use may reduce the quality of the product and should be used carefully.

 1.3 According to the limitation of the drawing process, if the steel wire is not lubricated in the mold, the surface of the steel wire will be destroyed, so a little black lubricant residue on the surface of the bright steel wire belongs to the process residue. If there is no residue, it can be proved that the surface of the steel wire has been destroyed.

There is no scientific basis for judging whether the surface of a bright steel wire can be a little oily. It is also very blind and lacks scientific experience. Of course, the bright steel wire of the pickling process is excluded.

 1.4 In the actual production, the individual suggests that the gloss and surface finish of the first coil of steel produced by the normal operation of the water tank puller should be judged as the criterion.

 

 2. Tolerance range: According to the national standard, the tolerance range of bright steel wire should be ±0.03mm.

 2.1 According to the experience gained in actual production management, it is very scientific to use national standards to take the tolerance range of steel wire. Not only can it establish a standard for industrial production, but it is also very economical in actual use, which can improve the cost performance of the production steel wire, and will not affect the welding effect of the condenser and the evaporator and increase the de-soldering rate.

 2.2 In recent years, the condensers and evaporator factories that actually use steel wires have been designed to ensure the yield of products and reduce the rate of weld removal during welding. The tolerance range is limited to ±0.02 mm or less. According to actual production surveys, This is only to eliminate the possibility of desoldering caused by the steel wire in the production, and it is not possible to substantially reduce the desoldering rate on the original basis.

 The tightness of the welding of the steel wire with the Bondi tube is generally related to the current, voltage, welding time of the welder, the roundness of the Bondi tube and the similarity of the Bondi tube and the steel wire material. Controlling the tolerance range of the steel wire within ±0.02 mm or less is a problem, and the processing cost of the steel wire is increased.

 

 3. Special notice is the use of pseudo-bright steel wire. If the acid stain is not used to remove the surface oil (acid wash pollutes the environment), the condenser and evaporator will be coated with plastic powder or paint outside the oil. Layers, which will shorten the life of the product. For the original meaning of bright steel wire, the pseudo-bright steel wire is a counterfeit product in the bright steel wire.

 The pseudo-bright steel wire is essentially a black steel wire, but the polishing effect of the wire drawing process makes the black lubricant on the surface of the black steel wire polished and has the same luster as the bright steel wire. The harm is that the method will be black lubricant. It is embedded in the surface of the steel wire and is difficult to remove in subsequent production.

 

Send Inquiry

whatsapp

skype

E-mail

Inquiry